We’ve been having an odd winter here in New England – lots of snow over a very short period of time. We’ve had about 80 inches (or ~ 2 m) of snow in the last 20 days with more coming down as I write this. During the last storm I made the misguided decision to head out to photograph in the nearby woods. Misguided because the visibility was poor and the snow plows were not managing to keep up with the snow which made driving interesting. Once at the woods the snow was quite deep even on the normally well trodden paths which made for slow going.
Increasingly I will explore ideas with my iPhone before pursuing them further with my DSLR. A couple of the images from my iPhone are above, I was at least thigh deep in the snow in this part of the woods. As I maneuvered my tripod around in the deep snow I heard a funny creaking noise. At first I thought that was the wind blowing the trees, but there wasn’t any wind. Then I thought it must be someone else out and about, but I could see anyone. Very weird. I picked my tripod up out of the snow to get it into a better position and and two of the tree legs came up, the third stayed in the snow. It had come detached where it joined the metal frame. That was pretty much the end of my photography for the day.
I’m not sure if you can tell from the images above but the carbon fiber leg where it joined the frame had delaminated and was soft. It was also crinkled which explained why the tripod leg did not fully close – there was always just a tiny fraction of leg extended. The metal also looks like it is badly corroded. While I may send this old tripod back to Gitzo I’m not holding my breath that they would be able to help me out.
I do have a new tripod that I’ve been using as a travel tripod – a Really Right Stuff 24L. I may now supplement this with the 34L, a beefier version of the 24L. The 24L to me seems a bit weedy, the lower sections of the legs are particularly thin and make me wonder how solid the tripod can really be. I guess time will tell.
I was working on my project “Everyday Objects’ this weekend and shot the image above of what I believe is a wasp’s nest with my newly renovated tripod.
In reading about how to care for and maintain your tripod I actually went and read some of the manuals that are supplied with Gitzo, Really Right Stuff etc. style tripods. Not something that I would normally do being the type of person who shuns manuals in favor of a more intuitive exploration of the functions of a new piece of gear. You should have seen me trying to start the rental car in Iceland – but that’s a topic for another day.
Really Right Stuff tell you that ‘Sand and saltwater are your tripod’s worst environmental enemies.’ About half, if not more, of my tripod use is at the beach so it’s hardly any wonder then that my tripod finally started to complain recently after many years of good service.
Carbon fiber tripods such as my old Gitzo 1325 are generally simple to look after and should last for an exceptionally long time. I’d hoped that I’d only have to buy one tripod which now seems like wishful thinking but a few simple precautions should keep your tripod in good shape.
Wipe down the tripod legs with a damp cloth to remove mud, sand and salt water. Dry the legs off before collapsing.
Check all metal fittings for signs of corrosion and replace as necessary. Spare parts should be available from the manufacturer. Here’s a pdf of the parts for my 1325 tripod to see how it breaks down. The Gitzo Service Center can be found here. For old tripods spare parts can be a pain to find. It pays to anticipate future needs!
Disassembly and a more thorough cleaning is recommended after immersing one or more of the leg joints in water and getting water up inside the tripod legs.
This is a case of do as I say rather than do as I do. Although I’m sure if I followed my own advice I would have had less problems over the years.
Water, mud, sand or saltwater inside the legs causes a number of problems, including :
initiation of corrosion on some of the internal parts that is difficult to diagnose until too late
causes the bushings to swell making it difficult to open the tripod legs
Taking the tripod apart is remarkably easy even though I was convinced that I would break the whole thing if I attempted it. While the process described here is for the Gitzo 1325 from digging around it looks as though most of the equivalent tripods from other manufacturers come to disassemble in a very similar way.
Things to have on hand during disassembly:
Spare bushings if you’ve been having problems
Shop rags or paper towels for clean up and drying the legs.
WD-40, used sparingly this can cut through the muck on even the most sadly neglected of tripods.
An old tooth brush is handy to clean grit and grime from the tripod collars and threads.
A good lubricant for the nicely cleaned threads. I used Lanocote because I had a tub handy.
Here’s the lower section of one the legs:
Diassembly is simply a matter of unscrewing the leg collar all the way until it releases as shown here:
Hopefully you can then just pull on the leg and it will smoothly come free (- or not if you read my previous post on my disassembly efforts):
The carbon fiber bushing appears to sit under the join of the two legs and is compressed as you screw the collar tight, holding the leg where you’ve set it. You can see where it normally is in the picture above.
The plastic guides keep the leg centered as it slides inside the fatter leg above. The plastic bushings were particularly salty but cleaned up nicely as shown below.
If you look carefully you can see that the salt build up has caused some wear of these guides. I also found that it could be tricky to get these guides to sit in groove in the tripod leg properly after removing them for cleaning. This was easily fixed by compressing them as shown below.
This compression was sufficient to close the gap that you can see in the upper guide which meant that the guide seated more closely into the groove on the tripod leg making it easier to reassemble the leg.
Getting everything back together is simply a matter of reversing the process. It’s relatively easy to do, although it might take you the best part of an evening to clean up the entire tripod or longer if you have to deal with stuck leg joints as I did!
Good luck and let me know if you have any suggestions.
As I was setting up my tripod for this shot this summer as I collapsed, de-telescoped, closed or whatever you call it, one of the legs the rubber foot shot off sending me scrambling to find it. Luckily I did! The glue had finally given up on the Gitzo 1325 legs of my tripod. Not bad after taking a beating for 8 years. I got a two part adhesive and glued it back in place and my tripod problems were over. Or at least I thought my tripod problems were over.
When I was using the tripod this week one i found that one of the legs was impossible to fully extend. Years of neglect had finally come home to roost. Photographing in and around the ocean means that your gear takes a pounding. Ideally you would rinse the salt water off your gear with fresh water. There are obvious problems doing that with cameras and lenses but you can and should do some clean up of your gear with a soft damp cloth after you’ve been out. I do this as needed after every shoot but I’ve never properly cleaned my tripod. This has largely been out of fear of getting the tripod to pieces and not being able to get it back together again.
I actually found that taking the tripod to pieces was much easier than I’d expected. On the old Gitzo that I have it’s simply a matter of unscrewing the leg lock the whole way and then pulling on the leg. The one that was stuck needed me to stand on the head of the tripod and then yank hard on the leg. Eventually it yielded to force! While the tripod was in pieces I took the opportunity to clean up the threads both on the leg and on the screw lock. The leg locks had been making awful grinding noises for years, presumably from sand and salt getting in there. This was easy enough to do with a rag for the legs and a toothbrush to get into the locks. As an aside I had always been taught to extend the tripod fattest section first, which of course meant that the lower section lock ended up under water the first time I used the tripod at the beach. While this advice is generally sound I typically have the lower section extended the width of my hand – about 4 inches – and then when working at the beach this is the first section that gets extended.
At the top of the tripod legs I found 3 bushings – two plastic and one that could easily be carbon fiber. Trying to get the legs back together was a little tricky and after a little bit of trial and error I realized that it was the plastic bushings causing the problems. I took these off the tripod and wound them into a tighter circle and then when they went back on the tripod the plastic stayed in this tighter configuration long enough to allow me to reassemble the whole thing relatively easily,
It was quite an educational process and easy enough that I could have been doing regularly all along!